Positioning of Cutting Dies Depending on Work Style and Margin

IconDangerInjury.png

Caution: If the subject setting is set to half sheet positioning and if a work style that does not support half sheet positioning is selected when switching to it, the system automatically switches to the appropriate full sheet positioning.

"Single-sided (no back)" or "Perfecting" or "Sheetwise (front and back)" work styles

Positioning

All margins equal 0

At least one margin unequal 0

 

evenly distributed in horizontal direction

side by side in horizontal direction
Packaging_PosButton200100.png


 

The cutting dies are cen­tered vertically on the paper.
Stanzform_Rand0_mittig.png

 
Stanzform_Randx_mittig.png

 
Packaging_PosButton300101.png


 

The cutting dies are posi­tioned vertically on the gripper margin on the paper.
Stanzform_Rand0_untenGreiferrand.png

 
Stanzform_Randx_untenGreiferrand.png

 

Depending on the height of the margin, the cut blocks or the bleed of the cutting die are positioned on the gripper margin, in the same way as for the "Imposition" mode.
Packaging_PosButton600102.png


 

The cutting dies are posi­tioned vertically on the paper with a variable off­set to the lower paper edge.
Stanzform_Rand0_unten.png

 
Stanzform_Randx_unten.png

 

Depending on the height of the margin, the cut blocks or the bleed of the cutting die are positioned on the set offset to the lower paper edge.
Packaging_PosButton700103.png


 

The cutting dies are posi­tioned vertically on the paper with a variable off­set to the lower paper edge and horizontally with a variable offset to the left paper edge.
Stanzform_Rand0_variable.png

 
Stanzform_Randx_variable.png

 

Depending on the height of the left or lower margin of the cutting die, either the cut blocks or the bleed of the cutting die are positioned on the set offset to the left or lower paper edge.

 

evenly distributed in vertical direc­tion

side by side in vertical direction
Packaging_PosButton400104.png


 

The paper is cut through the vertical center and the cutting dies on both halves of paper are posi­tioned on the horizontal center.
Stanzform_Rand0_vertikalmittighorizontal.png

 
Stanzform_Randx_vertikalmittigeven.png

 
Packaging_PosButton500105.png


 

The paper is cut through the vertical center and the cutting dies on both halves of paper are posi­tioned horizontally on the "cut" margin on the left and right.
Stanzform_Rand0_vertikalmittig.png

 
Stanzform_Randx_vertikalmittig.png

 

Depending on the height of the left or lower margin of the cutting die, either the cut blocks or the bleed of the cutting die are positioned on the gripper margin, in the same way as for the "Imposition" mode.

"Work-and-turn" work style

Positioning

All margins equal 0

At least one margin unequal 0

 

evenly distributed in vertical direc­tion

side by side in vertical direction
Packaging_PosButton200106.png


 

The cutting dies are posi­tioned horizontally on the paper on the "work-and-turn edge".
Stanzform_EUmschl_Rand0_horizontal.png

 
Stanzform_EUmschl_Randx_horizontal.png

 
Packaging_PosButton300107.png


 

The cutting dies are posi­tioned on the paper hori­zontally on the "work-and-turn edge" and verti­cally on the gripper mar­gin.
Stanzform_EUmschl_Rand0_horizontalUmvertikalGR.png

 
Stanzform_EUmschl_Randx_horizontalUmvertikalGR.png

 

Depending on the height of the margin, the cut blocks or the bleed of the cutting die are positioned on the gripper margin, in the same way as for the "Imposition" mode.
Packaging_PosButton600108.png


 

The cutting dies are posi­tioned on the paper hori­zontally on the "work-and-turn edge" and verti­cally with a variable offset to the lower paper edge.
Stanzform_EUmschl_Rand0_horizontalUmvertikalvariabel.png

 
Stanzform_EUmschl_Randx_horizontalUmvertikalvariabel.png

 

Depending on the height of the margin, the cut blocks or the bleed of the cutting die are positioned on the set offset to the lower paper edge.
Packaging_PosButton700109.png


 

The cutting dies are posi­tioned on the paper hori­zontally with a variable offset to the left paper edge and vertically with a variable offset to the lower paper edge.
Stanzform_EUmschl_Rand0_horizontalvertikalvariabel.png

 
Stanzform_EUmschl_Randx_horizontalvertikalvariabel.png

 

Depending on the height of the left or lower margin of the cutting die, either the cut blocks or the bleed of the cutting die are positioned on the set offset to the left or lower paper edge.

Positioning

 

 
Packaging_PosButton400110.png

 

Packaging_PosButton500111.png


 

Half sheet positioning is not supported in "work-and-turn".

"Work-and-tumble" work style

Positioning

All margins equal 0

At least one margin unequal 0

 

evenly distributed in horizontal direction

side by side in horizontal direction
Packaging_PosButton200112.png


 

The cutting dies are posi­tioned vertically on the "work-and-tumble edge" on the paper.
Stanzform_EUmst_Rand0_vertikalUmstk.png

 
Stanzform_EUmst_Randx_vertikalUmstk.png

 
Packaging_PosButton300113.png


 

The cutting dies are posi­tioned vertically on the gripper margin on the paper.
Stanzform_EUmst_Rand0_vertikalGR.png

 
Stanzform_EUmst_Randx_vertikalGR.png

 

Depending on the height of the margin, the cut blocks or the bleed of the cutting die are positioned on the gripper margin, in the same way as for the "Imposition" mode.
Packaging_PosButton600114.png


 

The cutting dies are posi­tioned vertically on the paper with a variable off­set to the lower paper edge.
Stanzform_EUmst_Rand0_vertikaluPk.png

 
Stanzform_EUmst_Randx_vertikaluPk.png

 

Depending on the height of the margin, the cut blocks or the bleed of the cutting die are positioned on the set offset to the lower paper edge.
Packaging_PosButton700115.png


 

The cutting dies are posi­tioned on the paper hori­zontally with a variable offset to the left paper edge and vertically with a variable offset to the lower paper edge.
Stanzform_EUmst_Rand0_variabelPk.png

 
Stanzform_EUmst_Randx_variabelPk.png

 

Depending on the height of the left or lower margin of the cutting die, either the cut blocks or the bleed of the cutting die are positioned on the set offset to the left or lower paper edge.

Positioning

 

 
Packaging_PosButton400116.png

 

Packaging_PosButton500117.png


 

Half sheet positioning is not supported in "work-and-tumble".